CONICAL
ADAPTERS - Direct Connect 1/16" and 1/8" OD Rigid and Semi-Rigid Tubing to Peristaltic Tubing / Accept.020" - 1/8" (.50 - 3.2mm) ID Peristaltic Tubing / Biocompatible Flowpath With Excellent Chemical Compatibility |
|
Upchurch Scientific® Conical Adapters provide a reliable connection between rigid/semi-rigid tubing and peristaltic-type flexible tubing, such as Tygon® and PharMed®. These adapters are composed of a PEEK™ polymer female nut, our Super Flangeless™ ferrule system and a Tefzel® (ETFE) or PEEK conical adapter body. The narrow coned end of the adapter body allows peristaltic tubing to slide on easier than it does onto conventional barbed adapters. Peristaltic tubing is also easier to remove from our Conical Adapters, since no cutting or excessive pulling is required. |
PERISTALTIC TUBING ADAPTERS | |
These unique
adapters connect peristaltic tubing to standard 1/16" or 1/8" OD
tubing. A specially-designed nose allows the peristaltic tubing to be
press fit and sealed by both the small barbs on the nose and the retainer
sleeve. Your 1/16" OD tubing may then be connected with the
Flangeless Fittings supplied with the adapter. To connect your peristaltic
tubing to 1 /8" OD tubing, simply replace the supplied fittings with
your choice of flangeless fittings. One popular application for these adapters is to use them as "stops" for your peristaltic pump. By doing so, you can reduce the amount of peristaltic tubing required for your flowpath, thus reducing cost. |
CONICAL ADAPTER ASSEMBLIES | |||
Artikelnummer | Beschreibung | ||
P-794 | Conical Adapter Connects 1/16" OD rigid to .020"-.030" (.50 -.75mm) ID peristaltic tubing | ||
P-797 | Conical Adapter Connects 1/16" OD rigid to 1/16"-3/32" (1.55 - 2.40mm) ID peristaltic tubing | ||
P-798 | Conical Adapter Connects 1 /8" OD rigid to 1/16- 3/32" (1.55 - 2.40mm) ID peristaltic tubing | ||
P-799 | Conical Adapter |
||
CONICAL ADAPTER REPLACEMENT PARTS | |||
F-156 | Female Nut, 1/8" for P-798 and P-799,1/4-28, Black PEEK | ||
P-420 | Female Nut, 1/16" for P-794 and P-797,1/4-28, Natural PEEK | ||
P-259 | Super Flangeless Ferrule, 1/16" ETFE ferrule with stainless steel lock ring | ||
P-359 | Super Flangeless Ferrule, 1/8" ETFE ferrule with stainless steel lock ring | ||
P-690 | Conical Adapter Body for P-797 and P-798, Natural ETFE | ||
P-691 | Conical Adapter Body for P-799, Natural ETFE | ||
P-692 | Conical Adapter Body for P-794, Natural PEEK | ||
PERISTALTIC TUBING ADAPTER Set | |||
P-757 | Adapter (pkg. of 2) for use with .048" -.110"(1.20- 2.80mm) ID tubing with ODs up to .180" (4.55mm) | ||
P-767 | Large Bore Adapter (pkg. of 2) for use with .100"-.150" (2.55 - 3.80mm) ID tubing with ODs up to.250" (6.35mm) |
SUPER FLANGELESSTM TO LUER ADAPTERS | LUERTIGHTTM
FITTINGS - Luer Fittings for Teflon and Tefzel Tubing / Quick Disconnect and Barbless / For 1/16" and 1/8" OD Tubing |
Upchurch
Scientific® Super Flangeless to Luer Adapters offer higher pressure
holding capabilities than other luer adapters on the market, holding
1/S" OD tubing to pressures in excess of 1,200 psi (83 bar)! Made of
PEEK™ polymer, these connectors are durable, biocompatible and offer
excellent solvent resistance. The Super Flangeless lock ring is made of
316 stainless steel and does not contact the fluid path. Super Flangeless to Luer Adapters are designed to be used on semirigid and rigid tubing, such as Teflon®, Tefzel® (ETFE), PEEK and stainless steel. Unlike most other luer adapters, these products do not require additional nuts and ferrules. Please Note: assembly of this fittings system requires a special swaging tool, T-100. Please contact us for more information. |
Upchurch
Scientific LuerTight fittings are specifically designed to connect semi-rigid
fluoropolymer tubing without barbs or nuts! By integrating ferrules into the luer
bodies, LuerTights will reliably hold your Tefzel tubing in place while
giving you the convenience of a luer connection - a great improvement over barbed
luer connections. An inline set of LuerTight fittings provides a quick and easy
disconnection option. LuerTight connections are also less bulky and more economical
than nut to luer style fittings. The bodies of these products are manufactured from polypropylen and the ferrules are made of Tefzel (ETFE). Each LuerTight fitting conforms to ISO requirements for medical luer taper configuration and performance (45psi/3.1 bar). |
Artikelnummer | Bild | Beschreibung | |||
SUPER FLANGELESS TO LUER ADAPTERS | |||||
P-687 | Super Flangeless To Male Luer, PEEK, with SST lock ring | ||||
P-688 | Super Flangeless To Female Luer, PEEK, with SST lock ring | ||||
LUERTIGHT FITTINGS SYSTEMS | |||||
P-837 | LuerTight System for 1/16" OD tubing Contains (1) P-835 Fitting, (1) P-836 Fitting and (1) P-830T Set Plug | ||||
P-838 | LuerTight System for 1/8" OD tubing Contains (1) P-830 Fitting, (1) P-831 Fitting and (1) P-830T Set Plug | ||||
LUERTIGHT FITTING COMPONENTS | |||||
Artikelnummer | Beschreibung | ||||
P-830 | Female Fitting for 1/8" OD tubing w/ (1) ferrule | ||||
P-830T | Set Plug to swage ferrules into P-835 and P-830 | ||||
P-831 | Male Fitting for 1/8" OD tubing, no ferrule required | ||||
P-835 | Female Fitting for 1/16" OD tubing w/ (1) ferrule | ||||
P-836 | Male Fitting for 1/16" OD tubing w/ (1) ferrule | ||||
Female = Internal threads; Male = External threads |
QUICK
CONNECT LUER ADAPTERS - Derlin®, Polypropylene, Tefzel® (ETFE) and PEEK™ Versions / 1/4-28,10-32, 5/16-24 and M6 Threaded Ports |
These luer
adapters were designed to work in a variety of applications. By connecting
any male luer to any female luer, you can create your own quick connect
union or adapter. Each Upchurch Scientific® Quick Connect Luer Adapter
has a .04" (1.0mm) or a .05" (1.3mm) thru-hole and conforms to
ISO requirements for medical luer taper configuration and performance (45
psi/3.1 bar). High Pressure (10-32) or Low Pressure (1 /4-28, 5/16-24 and M6) chapters. Please Note: Our Female Quick Connect Luer Adapters can be used with any of the Male Luers, i.e., those with and without lock hubs. |
QUICK CONNECT LUER ADAPTERS | |||||||||
Artikelnummer | Beschreibung | Body Material | Lock Hub Material | Thru-hole | Bild | ||||
P-604 | F Luer to 1/4-28 M(1) | Nat. Delrin | N/A | .05" (1.3mm) | |||||
P-605 | M Luer to 1/4-28 M(1) | Nat. Detain | None (Slip type) | .05" (1.3mm) | |||||
P-618 | F Luer to 1/4-28 M(1) | Nat. PP | N/A | .05" (1.3mm) | |||||
P-619 | M Luer to 1/4-28 M(1) | Nat. PP | None (Slip type) | .05" (1.3mm) | |||||
P-624 | F Luer to 1/4-28 M(1) | Nat ETFE | N/A | .05" (1.3mm) | |||||
P-625 | M Luer to 1/4-28 M(1) | Nat ETFE | None (Slip type) | .04" (1.Omm) | |||||
P-628 | F Luer to 1/4-28 F(1) | Nat ETFE | N/A | .04" (1.Omm) | |||||
P-629 | F Luer to 10-32 F(2) | Nat ETFE | N/A | .04" (1.Omm) | |||||
P-629BLK | F Luer to 10-32 F(2) | Black ETFE | N/A | .04" (1.Omm) | |||||
P-642 | F Luer to 10-32 M(2) | Nat. ETFE | N/A | .05" (1.3mm) | |||||
P-655 | M Luer to 1/4-28 F(1) | Red PEEK | Black PEEK | .05" (1.3mm) | |||||
P-656 | M Luer to 10-32 F(2) | Nat. PEEK | Black PEEK | .05" (1.3mm) | |||||
P-657 | M Luer to M6 F(1) | Black PEEK | Black PEEK | .05" (1.3mm) | |||||
P-658 | F Luer to 1/4-28 F(1) | Red PEEK | N/A | .05" (1.3mm) | |||||
P-659 | F Luer to 10-32 F(2) | Nat. PEEK | N/A | .05" (1.3mm) | |||||
P-660 | F Luer to M6 F(1) | Black PEEK | N/A | .05" (1.3mm) | |||||
P-661 | F Luer to 5/16-24 M(1) | Nat. ETFE | N/A | .05" (1.3mm) | |||||
P-675 | M Luer to 1/4-28 F(1) | Red ETFE | Nat PP | .05" (1.3mm) | |||||
P-677 | M Luer to M6 F(1) | Black ETFE | Nat PP | .05" (1.3mm) | |||||
P-678 | F Luer to 1/4-28 F(1) | Red ETFE | N/A | .05" (1.3mm) | |||||
P-680 | F Luer to M6 F(1) | Black ETFE | N/A | .05" (1.3mm) | |||||
P-683 | M Luer to 1/4-28 M(1) | Nat PEEK | Black PEEK | .04" (1.Omm) | |||||
P-686 | F Luer to M6 M(1) | Black ETFE | N/A | .05" (1.3mm) | |||||
SYRINGE WITH MALE LUER LOCK | |||||||||
Artikelnummer | Beschreibung | Thru-hole | |||||||
B-310 | 10cc
Disposable Luer-Lock Syringe |
.05" (1.3mm) | |||||||
F=Female (internal) threads: M=Male (external) threads, Nat =Natural; N/A = Not Applicable; PP = Polypropylene (1)'Threaded end of this adapter has a flat-bottom configuration, (2) Threaded end of this adapter has a coned configuration. |
BARBED
ADAPTERS - Three Barb Sizes, for 1/16", 1/8" and 3/16" ID Flexible Tubing / Adapt to 1/4-28 Flat-Bottom, 5/16-24 Flat-Bottom or 10-32 Coned Receiving Ports / Available with .04", .08" and .10" Thru-holes |
FEMALE
LUER-TO-BARB ADAPTERS - Three Barb Sizes for 1/16", 3/32", and 1/8" ID Flexibl / Adapt to Any Male Luer / Made of Tefzel (ETFE) |
|
These Upchurch Scientific® adapters make it easy to connect flexible tubing to any standard 1/4-28 or 10-32 receiving port. Simply thread the adapter into a receiving port and slip tubing over the barbed stem to create a reliable low pressure connection. | Connect
peristaltic tubing easily with Upchurch Scientific Female Luer-to-Barb Adapters.
Made of ETFE, these products have excellent resistance to most solvents used in
analytical analyses, and are especially well suited for SPE applications. These
adapters can be used at up to 80°C, compared to only 40°C for similar
polypropylene products. Each adapter conforms to ISO requirements for medical luer taper configuration and performance (45 psi/3.1 bar), and will work with both slip-type male luers and luer lock connectors. |
Artikelnummer | Beschreibung | Bild | Material | Thru-hole | |||||
BARBED TO 10-32 CONED MALE ADAPTERS | |||||||||
P-663 | For use with 1/16" (1.55mm) ID tubing | ETFE | .04" (1.0mm) | ||||||
P-664 | For use with 1/8"(3.20mm)ID tubing | ETFE | .04" (1.0mm) | ||||||
P-665 | For use with 3/16" (4.75mm) ID tubing | ETFE | .04" (1.0mm) | ||||||
BARBED TO 1/4-28 FLAT-BOTTOM MALE ADAPTERS | |||||||||
P-646 | For use with 1/16" (1.55mm) ID tubing | ETFE | .04" (1.0mm) | ||||||
P-647 | For use with 1/8" (3.20mm) ID tubing | ETFE | 0.80" (2.0mm). | ||||||
P-648 | For use with 3/16" (4.75mm) ID tubing | ETFE | .10" (2.5mm) | ||||||
P-668 | For use with 1/16" (1.55mm) ID tubing | PEEK™ | .04" (1.0mm) | ||||||
P-692 | For use with.020" to 1/32" (.5 to.80mm) ID tubing | PEEK | .02"(0.5mm) | ||||||
BARBED TO 5/16-24 FLAT-BOTTOM MALE ADAPTERS | |||||||||
P-689 | For use with 3/16" (4.75mm) ID tubing | ETFE | .10" (2.5mm) | ||||||
FEMALE LUER-TO-BARB ADAPTERS | |||||||||
Artikelnummer | Beschreibung | Material | Thru-hole | ||||||
P-870 | For
use with 1/16" (1.SSmm) ID tubing A=.030" B-.063"
C=.106" D=,700" E=,598" |
ETFE | 0.30" (0.76mm) | ||||||
P-871 | For
use with 3/32" (2.40mm) ID tubing A=.056" B-102"
C=.145" D=.100" E=.648" |
ETFE | 0.56" (1.42mm) | ||||||
P-872 | For
use with 1/8" (3.20mm) ID tubing A=.080" 8=.137"
C=.187" D=.100" E=.733" |
ETFE | 0.80" (2.03mm). |
POLYPROPYLENE BARBED ADAPTERS | |
Use these
barbed adapters to connect peristaltic-type flexible tubing for general,
low pressure applications, such as plumbing ISMATEC® Peristaltic Pumps. Polypropylene is a Class VI material. Due to the low melt point of polypropylene, these adapters are not autoclavable, however, they can be sterilized via gamma radiation. |
Artikelnummer | Beschreibung | Bild | Menge | |
BARB TO SLIP-TYPE MALE LUER ADAPTERS (Packung a 10 Stück) | ||||
P-854 | Male Luers (Slip-type) for use with 1/16" ID (1 55mm) tubing A=.046" B=.064" C=.090" C=.129" E=.711" F=.198" H=.384" | Stck. | ||
P-855 | Male Luers (Slip-type) for use with 3/32" ID (2.40mm) tubing A=.069" B=.097" C=.138" D=.128" E=.803" F=.290" H=.385" | Stck. | ||
P-856 | Male Luers (Slip-type) for use with 1/8" ID (3.20mm) tubing A=.096" B-.129" C=.182" D=.129" E=.889" F=.383" H=.377" | Stck. | ||
These slip-type male luer fittings are for use in systems which luer lock rings are not desired | ||||
BARB TO MALE LUER WITH LOCK RING ADAPTERS | ||||
P-850 | Male Luers with Lock Ring for use with 1/16" ID (1.55mm) tubing A=.049" R-.065" C=.090" E=.583" F=.434" | Stck. | ||
P-851 | Male
Luers with Lock Ring for use with 3/32" ID (240mm) tubing A=.071" B=.100" C=.139" E=.681" F=.436" |
Stck. | ||
P-852 | Male Luers with Lock Ring for use with 1/8" ID (3.20mm) tubing A=.099" B=.132" C=.184" E=.777" F=.436" | Stck. | ||
P-853 | Male Luers with Lock Ring for use with 5/32" ID (4,00mm) tubing A=.108" B=.164" C=.231" E=.874" F=.436" | Stck. | ||
BARB TO FEMALE LUER-LOCK CONNECTORS | ||||
P-857 | Female Luer Connectors for use with 1/16" ID (1.55mm) tubing A=.030" B=.063" C=.106" D=.100" E=.598" F=.253" | Stck. | ||
P-858 | Female Luer Connectors for use with 3/32" ID (2.40mm) tubing A=.056" B=.102" C=.145" D=.100" E=.648" F=.253" | Stck. | ||
P-859 | Female Luer Connectors for use with 1/8" ID (3.20mm) tubing A=.080" B=.135" C=.187" D=.100" E=.733" F=.253" | Stck. | ||
BARBED UNION CONNECTORS | ||||
P-801 | Barbed Connectors
to connect 1/16" ID (1.55mm) tubing to 1/16" ID (1.55mm) tubing A=.046" B=.063" C=.101" D=.100" E=.658" |
Stck. | ||
P-802 | Barbed Connectors
to connect 1/8" ID (3.20mm) tubing to 1/8" I D(320mm) tubing A=.085" B=.126" C=.182" C=.098" E=.791" |
Stck. | ||
P-803 | Barbed Connectors
to connect 3/16" ID (4.75mm) tubing to 3/16" ID (4.75mm) tubing A=.122" B=.157" C=.275" D=.126" E=1.179" |
Stck. | ||
P-804 | Barbed Connectors
to connect 1/4" ID (6.35mm) tubing to 1/4" ID (6.35mm) tubing A=.185" B=.247" C=.342" D=.163" E=1.279" |
Stck. | ||
P-805 | Barbed Connectors
to connect 3/8" ID (9.55mm) tubing to 3/8" ID (9.55mm) tubing A=.248" B=.373" C=.466" D=.249" E=2.103" |
Stck. | ||
P-806 | Barbed Connectors
to connect 1/2" ID (12.7mm) tubing to 1/2" ID (12.7mm) tubing A=.390" B=.496" C=.598" D=.249" E=2.047" |
Stck. | ||
BARBED REDUCING ADAPTERS | ||||
P-807 | Barbed Reducing
Adapters to connect 1/8" ID (3.20mm) tubing to 1/16" ID (1.55mm) tubing A=.081" B=.120" C=.170" D=.104" E=.755" G=.102" H=.048" I=.67" |
Stck. | ||
P-808 | Barbed
Reducing Adapters to connect 3/16" ID (4.75mm) tubing to 1/8" ID (3.20mm) tubing A=.126" B=.187" C=.285" D=.131" E=1.245" G=.181" H=.085" I=.125" |
Stck. | ||
P-809 | Barbed
Reducing Adapters to connect 1/4" ID (6.35mm) tubing to 3/16" ID (4.75mm) tubing A=.139" B=.209" C=.355" D=.125" E=1.561" G=.270" H=.139" I=.184" |
Stck. | ||
P-810 | Barbed Reducing
Adapters to connect 3/8" ID (9.55mm) tubing to 1/4" ID (6.35mm) tubing A=.248" B=.371" C=.466" D=.249" E=2.057" G=.345" H=.188" I=.249" |
Stck. | ||
"Y" BARBED CONNECTORS | ||||
P-860 | "Y"
Barbed Connectors for use with 1/16" ID (1.55mm) tubing A=.047" B=.066" C=.092" E=.508" F=.345" |
Stck. | ||
P-861 | "Y" Barbed Connectors for use with 3/32" ID (2.40mm) tubing A=.070" B=.099" C=.137" E=.757" F=.521" | Stck. | ||
P-862 | "Y" Barbed Connectors for use with 1/8" ID (3.20mm) tubing A=.095" B=.126" C=.183" E=1.017" F=.70" | Stck. | ||
P-863 | "Y" Barbed Connectors for use with 3/16" ID (4.75mm) tubing A=.157" B=.197" C=.280" E=1.470" F=1.051" | Stck. | ||
P-864 | "Y"
Barbed Connectors for use with 1/4" ID (6.35mm) tubing A=.189" B=.266" C=,372" E=2.040" F=1.405" |
Stck. |
ENGLISH THREADED ADAPTERS | |||||||
Artikelnummer | Beschreibung | Material | Thru-hole | Swept Volume | Pressure Rating (psi/bar) | Bild | |
5/16-24 and 1/2-20 Adapters | |||||||
6000-076 (1) | 5/16-24 M to 10-32F | PEEK™ | .066" | 49.8µl | 3,000/207 | ||
P-135 | 5/16-24 F to 1/4-28F | PEEK™ | .080" | 4.1 µl | 1,000/69 | ||
P-649 | 5/16-24 F to 1/4-28M | Kel-F® | .063" | 24.5 µl | 1,000/69 | ||
P-674 | 5/16-24 F to 1/4-28M | Kel-F® | .040" | 9.9 µl | 1,000/69 | --------------- | |
P-681 | 5/16-24 F to 1/4-28M | Kel-F® | .125" | 96.6 µl | 1,000/69 | --------------- | |
P-718 | 5/16-24 M to 1/4-28 F | Kel-F® | .040" | 10.3 µl | 1,000/69 | ||
P-684 | 1/2-20 F to 1/4-28M | Kel-F® | .130" | 121.7 µl | 250/17 | ||
U-659 | 5/16-24 F to 1/2-20F Includes (1) U-650 / U-655 Fittings | PEEK™ | Tapered(2) | 42.0 µl | 250/17 | ||
U-665 | 1/2-20 F to 1/4-28F | PEEK™ | .063" | 6.6 µl | 250/17 | ||
Female 10-32 Coned to 1/4-28 Adapters | |||||||
P-627 | 10-32 F to 1/4-28F Includes (1) F-300 Fitting | PEEK™ | .020" | 0.30 µl | 1,000/69 | ||
1583 | 10-32 F to 1/4-28F Includes (1) U-400/U-401 Fittings | SST | .040" | 0.60 µl(3) | |||
F =
Female (internal) threads; M = Male (external) threads (1)For use with Rheodyne Preparative-Scale Injector Valves (2)Thru-hole tapers from .188 to .125': (3)The pressure rating of this stainless steel adapter exceeds the pressure holding ability of the fittings and tubing used with it |
ENGLISH THREADED ADAPTERS | ||||||
Artikelnummer | Beschreibung | Material | Thru-hole | Swept-Volume | Pressure Rating (psi/bar) | |
Female to male 10-32 to 1/4-28 Adapters | ||||||
P-652 | 1/4-28 F to 10-32 M | PEEK™ | .030" | 6.7 µl | 1,000/69 | |
P-654 | 1/4-28 F to 10-32 M, XL | PEEK™ | .030" | 9.5 µl | 1,000/69 | |
P-669-01 | 10-32 F to 1/4-28 M | PEEK™ | .040" | 6.6 µl | 1,000/69 | |
P-671 | 1/4-28 F to 1/4-28 M | Teflon® | .040" | 8,0 µL | 1,000/69 | |
P-672 | 1/4-28 F to 10-32 Flat M | PEEK™ | .050" | 1 1.4 µL | 1,000/69 | |
1591 | 10-32 F to 1/4-28 M | SST | .040" | 6.0 µL | (1) | |
F=
Female (Internal) threads; M= Male (external) threads; XL = extra long (1) The pressure ratings of these adapters exceed the pressure holding ability of the fittings and tubing used with them. |
METRIC THREADED ADAPTERS - Good for Adapting Pharmacia® Columns with Hardware from Other Manufacturers | |
Female M6 Adapters | Female to Male M6 Adapters |
METRIC M6 THREADED ADAPTERS | ||||||
Artikelnummer | Beschreibung | Material | Thru-hole | Swept Volume | Pressure Ratings | |
Female M6 Adapters | ||||||
P-621(1) | 1/4-28 F to M6 F | Tefzell® | N/A | N/A | 1,000/69 | |
P-626 | 10-32 F to M6 F w/F-300 Fitting | PEEK™ | 0.3µl | 1,000/69 | ||
1587 | 10-32 F to M6 F w/U-400/U-401 | SST | 0.6µl | (2) | ||
Female to Male M6 Adapters | ||||||
P-920-01 | 10-32 F to M6 M | PEEK™ | 8.0µl | 1,000/69 | ||
P-650 | M6 F to 10-32 M Standard | PEEK™ | 6.7µl | 1,000/69 | ||
P-651 | M8 F to 10-32 M Waters®-compatible | PEEK™ | 7.2µl | 1,000/69 | ||
P-653 | M6 F to 10-32 M Extra Long | 9.5µl | 1,000/69 | |||
P-670 | M6 F to 1/4-28 M | Kel-F® | 2.6µl | 1,000/69 | ||
P-673 | 5/16-24 F to M6 M | Kel-F® | 9.9µl | 1,000/69 | ||
P-724 | M6 F to 5/16-24 M | Kel-F® | 10.3µl | 1,000/69 | ||
F =
Female (internal) threads; M = Male (external) threads (1)Do not use Tefzel nuts with P-621. (2)The pressure rating of this adapter exceeds the pressure holding ability of the fittings and tubing used with it. |
EXTERNAL NATIONAL PIPE THREAD ADAPTERS |
These
injection-molded adapters make connections to female 1/8" and
1/4" National Pipe Thread (NPT) ports. Molded from PEEK'" polymer, Upchurch Scientific® NPT Adapters are durable and chemically resistant. We provide a variety of female (internal) threads, as well as a male (external) threaded version, suitable for most low pressure fittings on the market today. All of our NPT adapters have a .062" (1.60mm) thru-hole, except U-504 and U-514 which have .125" (3.1 8mm) thru-holes. All included fittings are for 1/8" OD tubing, except U-504 and U-514, which come with fittings for 3/16" OD tubing. Please Note: Wrap the threads on the NPT side of these adapters with Teflon tape to ensure a leak-free seal. |
Artikelnummer | Bild | Beschreibung | Swept Volume | Tubing OD | |
1/8" MALE NPT ADAPTERS | |||||
U-510 | 1/8" NPT M
to 1/4-28 F Adapter, Red PEEK |
17.3µl | 1/8" | ||
U-511 | 1/8" NPT M to 1/4-28 M Adapter, Red PEEK | 40.2µl | N/A | ||
U-512 | 1/8" NPT M to M6 F Adapter, Black PEEK Includes (1) P-300/P-307 Fittings | 17.3µl | 1/8" | ||
U-514 | 1/8" NPT M to 5/16-24 F Adapter, Natural PEEK Includes (1) P-133/P-132 Fittings | 70.4µl | 3/16" | ||
1/4" MALE NPT ADAPTERS | |||||
U-500 | 1/4" NPT M to 1/4-28 F Adapter, Red PEEK Includes (1) P-300/P-308 Fittings | 17.3µl |
1/8" | ||
U-501 | 1/4" NPT M to 1/4-28 M Adapter, Red PEEK | 40.2µl | N/A | ||
U-502 | 1/4" NPT M to M6 F Adapter, Black PEEK Includes (1) P-300/P-307 Fittings | 1 7.3µl | 1/8" | ||
U-503 | 1/4" NPT M to 5/16-24 F Adapter, Natural PEEK Includes (1) P-360/P-131 Fittings | 17.3µl | 1/8" | ||
U-504 | 1/4" NPT M to 5/16-24 F Adapter, Natural PEEK Includes (1) P-133/P-132 Fittings | 70.4µl | 3/16" | ||